How Much Material To Cover A Chair Seat – Today we’re going to show you how to reupholster your dining room chairs to make them look brand new! This tutorial can be helpful if your chairs are already well-furnished but are unattractive or don’t fit your space. If you choose the right upholstery, upholstering your chairs can transform your dining room from looking dull, drab and old to lively, stylish and comfortable.
Before you gather your belongings, there are a few things you need to organize. The type of upholstery you use has a significant impact on the overall look of your dining room. So it is important to understand what is the color theme of your dining room and whether you want to match or contrast it. For example, if your walls are green, you should avoid using red, which will provide a sharp and attractive contrast.
How Much Material To Cover A Chair Seat
Also, when choosing the color of the material, consider the size of your dining room. A small room needs bright colors to make it feel spacious and less cluttered. Finally, the choice should be determined by how often the chair will be used. Small children in the house need heavy materials that do not fade easily and do not show stains.
Alora Raised Dots Stretch Dining Room Chair Seat Covers
Use staple/nail removal tools to remove the foam as well. My chair only had brackets and I was able to remove them with a flathead screwdriver and pliers. If there are nails, use this tool to remove them.
Cut the foam with an incredibly sharp knife (think commercial knife display) or insulation knife. We used an incredibly sharp serrated kitchen knife!
Take the seat + foam and place it on top of the polyester. Draw and trim about 5″ outside the edge.
Use a staple gun to secure the bottom batting, pulling tight as you go. Tip: It’s best to staple opposite sides until you reach about twelve stitches. Thus, the tightness will be the same.
Furniture Reupholstery Cost
Center the seat with the pattern print so that it is balanced and attached at least 4 inches down.
The print for this is still visible on the wrong side so I can see where to mark and cut to get the piece I want for the seat cushion. Fasten with a stapler, trimming the excess.
Tip: Pin before stapling to make sure the print stays in place.
This is optional, but recommended. Trace the seat cushion onto the dust cover, cut it out. Fold in half and staple. My husband and I recently purchased a set of Ikea Borge chairs for our dining room. The chairs looked great, but I knew the white fabric seats they came with wouldn’t last long in a house with two little boys and frequent dinner guests! I searched online and came across the Hearts Fabric website. After browsing their wonderful selection of quilted fabrics and cottons, I contacted Hearts to see if they would be interested in collaborating with me on this publication. Luckily they were!
Diy Upholstery: Easy Dining Chair Seat Covers
You can also find dining room chair covers here on Amazon at various prices.
I’ve tried covering chairs in two ways, so I’ll walk you through the process of attaching the fabric directly to the seat of the chair or sewing an elastic cover. These instructions include measurements for the Ikea Borge chairs, but can be modified for any chairs you have.
Let’s get started easy with Stapler! I used my heavy duty upholstery staple gun with a 1/4″ staple. For each seat, cut a rectangle that is 22 inches wide (the total width of the fabric is 44 inches, so you can get a 2 inch width) by 20.5 inches long (this measurement is at the bottom edge). These measurements give you 2″ to go behind the chair and 2 1/2″ for the other 3 sides.
To begin, place the seat against the wrong side of the fabric. Place 22 inches of fabric on the back of the seat beyond the side screw holes and center the support. Then place 2 more staples on either side of the center, for a total of 5 1 1/2″ staples – hammer the staples that are stuck.
Generic Comqualife Stretch Printed Dining Chair Seat Covers, Removable Washable Anti Dust Upholstered Chair Seat Cover For Dining Room,
Pull the fabric to remove creases and staple to the front of the chair with 5 staples, starting in the center and going out to the sides 2 inches apart. Then extend the sides and make a row of staples on each side, starting in the middle and working your way to the sides, for a total of 5 staples of 1 1/2″.
On the back of the chair, first fold a piece of fabric at the corner and staple it. Fold the other flap to the edge and pin. Then staple the front corners. Then take the triangle flap you just made and pinch it in the center of the chair and staple it. It will be slightly rounded at the top and have a small groove on each side of the corner.
Finally, staple the back corners. This is a bit tricky because there is a slot cut into the back of the chair. From the back of the chair, fold the fabric from the back edge of the seat to the center of the seat and staple. Then fold the fabric halfway down the seat until it’s nice and tight. Stapled in place. Next, take the triangle flap you just made, pull it tight and move all the slits into the center of the seat slot. Stapled in place. When you’re done, your fabric will look nice and smooth with no wrinkles! If desired, trim the remaining edges of the fabric.
This procedure needed some more work. If you’re using non-laminated fabric, it’s fine to remove it for cleaning, but for these specific chairs, you’ll need to remove the 4 screws holding the seat in place before removing. To use this method first print my free template (this link will open the PDF in a new window, you can save or print). The model is designed using Ikea Borge chairs, if they change the style in the future! Attach the stars to the template and glue the five template pages together. To use this pattern, your fabric will need a small amount so that you can spread it well into the corners of the chair. It’s a little harder than the cover that comes with the chair, so you get a nice soft top with laminated cotton. If you’re using a pattern, try making just one cover first to make sure it will work with your fabric!
What Is Upholstery And How Do You Choose The Best Fabric For Your Sofa?
To stabilize the fabric, use a stitch along the edges or use a sewing machine to create a zigzag stitch near the edge. Then fold the fabric down 5/8″ on each side (but not the corners) and sew with a 1/2″ seam allowance. This will create a shell for flexibility. You can see in the photo below that I used a roller foot to help slide the laminated cotton on my sewing machine more smoothly. If you don’t have one, you can try applying tape with a matte finish to the bottom of the regular foot to prevent it from sticking to the fabric.
On the wide side of the fabric (seat front), bring the corners right sides together and sew with a 1/2″ seam allowance from the fold.
On the remaining two edges (back corners), gather the cut piece to the right of the corner and sew 1/2″ from the edge of the fold to the edge of the fabric.
Thread a 3/8″ rubber band through the casing on all four sides. Use a good stiff elastic band with about 50 percent stretch (a 4-inch piece will stretch 6 inches before it starts to stretch). Start at the back corner and leave at least 5 inches out at the beginning and end. Place the cover around your seat and tighten it in all directions. Smooth out any wrinkles, pull the elastic and tie in a knot. If you don’t have a tight elastic, string will work and if you tie it into a tight bow, you can remove the cover to open it.
How To Reupholster Dining Room Chair Seat Covers
Both methods worked well and the final seats were almost identical. I preferred the stippling method because it was faster, easier to get a soft set and nice fabric without creases. And with laminated cotton, I never have to take it off to wash, wash, so laundry is a breeze! I also think the stapled seats could be more stable, as I’m a little concerned that all the thread holes in the stitched version are more prone to tearing under heavy use. But again, these differences are so subtle that no one can see them